Consulter la FAQ
Why doesn't StruxureWare or ISX Manager's mass configuration feature update or show password credentials on APC Network Management Card devices?
Devices with an embedded Network Management Card 1 include (but are not limited to ... Monitoring Units (ap9320, ap9340, NetBotz 200)
Can StruxureWare Data Center Expert be configured to alert for NetBotz 3xx, 4xx, and 5xx devices?
... Center Expert be configured to alert for NetBotz 3xx, 4xx ... NetBotz ... Center Expert monitoring NetBotz using HTTP or ... ... not alert for NetBotz 3xx, 4xx ... ... their integration with NetBotz Central, NetBotz devices were designed to alert for ... ... done to eliminate NetBotz Central as a single point of failure ... ... Although you can configure the NetBotz appliance through DCE ... handled by the NetBotz appliance directly. ... communications with the NetBotz device (and ... ... mean that the NetBotz is off- ... ... different than the NetBotz Rack Access AP9361, NetBotz 200, or NetBotz 250 which are ...
Why isn't Daylight Savings Time (DST) working properly when using custom settings and Network Time Protocol (NTP)?
... Network Management Card 1 (NMC1) ... ... Network Management Card 1 include (but ... , ap9340, NetBotz 200) ... Network Management Card 1 product family in ... ... daylight savings time setting and a NTP ... disregard the DST settings 90 seconds after ... ... ), Symmetra Single & Three Phase ... Network Management Card 1 devices (AP9617 ... Please download the new firmware from or through ISX Manager and StruxureWare Central update servers. If you are unable to upgrade, use the traditional daylight savings time setting .
Video: How do I configure APC Network Management Card network settings?
... Environmental Monitoring Unit 1 (AP9312TH) ... Network Management Card 1 (NMC1) ... ... Network Management Card 1 include (but ... , ap9340, NetBotz 200) ... TCP/IP settings prior to being ... ... Network Management Card 1 : ... Network Management Card 1 (AP9617, ... Network Management Card 1 (such as ... available options to configure the Network Management ... with it's initial settings : the Wizard ... ... Network Management Card 1 based devices are configured for a boot ... ... it is not configured on your DHCP ... ... methods below to configure /access the ... ... higher, are configured for DHCP Only ...
How can I mass configure a Network Management Card (NMC) or NMC embedded product?
How can I mass configure a Network Management Card (NMC) or NMC embedded product? ... can I mass configure or configure multiple Network Management ... ... Network Management Card 1 (NMC1) ... ... Network Management Card 1 include (but ... , ap9340, NetBotz 200) ... AP9312TH, MasterSwitch 1 /2) ... ... Card, mass configuration of those devices ... ... and uploading a single configuration file ( config .ini) ... ... modified through the config .ini ... , these four settings will be disregarded ... ... keyword will not configure Output Voltage, ... ... I obtain a config .ini ... file from a single Network Management Card ... ... firmware versions, one option is to retrieve the config .ini
Output relay state upon boot up of a Netbotz version 3 appliance.
Output relay state upon boot up of a Netbotz version 3 appliance. ... NetBotz ... Netbotz Version 3 output relay. ... Upon a reboot of the Netbotz appliance, the relays will go back to their default state. If there is an alert that is configured to trigger a state change on one of these buttons or switches, the state will then change as configured . ... This is working s designed .
Netbotz | What type of information can I see in a NetBotz SNMP trap?
... found in a NetBotz SNMP trap NetBotz NetBotz SNMP trap ... traps from a NetBotz device are a ... ... the same when configuring traps for StruxureWare ... the alarm action configuration for a trap ... ... a similar trap configuration but it is ... rather than the NetBotz OIDs. ... This article is designed to provide some ... ... Type: V 1 , V1TRAP VarBinding 1 : 1. ... ... VarBinding 11: 1 .3. ... ... VarBinding 13: 1 .3. ... ... .15 = 1 ... look at the NetBotz MIB, you ... that the trap parameters are listed under ... ... .netBotzAPC. NetBotz .netBotzTrapParms
NetBotz | Scheduling Periodic Reports
NetBotz v3 Wall ... NetBotz v3 Rack ... (nbrk0450/ 1 ), 550 ... NetBotz v2 and ... As designed , Periodic Sensor ... ... :30pm, 1 :15 pm ... ... this limitation and configure your appliance to ... ... interval value of 1 ,440 minutes ... ... the Advanced Scheduling settings and return to ... ... your Periodic Report settings . ... an interval of 1 ,440 minutes ( 1 day) the ... you saved the configuration . ... from reaching the 1 ,440 minute ... ... , but is never sent again before the next Disabled period ( 1 ,425 minutes later, at ...
HTTP and HTTPS turned off by default on NetBotz 4.7
... by default on NetBotz 4.7 ... NetBotz v3 Wall ... NetBotz v3 Rack ... (nbrk0450/ 1 ), 550 ... NetBotz v3 ( ... ... security features, designed to prevent unauthorized ... ... note that the NetBotz can still get ... ... that is currently configured and is simply ... ... :// Netbotz _IP) ... ... during initial console configuration ... : The serial config utility no longer ... from NetBotz Support will void your warranty. ... Welcome to NetBotz BotzWare V4.7.0 ... * To increase security, initial access to new NetBotz appliances has been * ... * use Advanced View and Data Center Expert to configure the appliance.
Mass Configuration in StruxureWare DCE does not copy passwords for APC devices or "Incomplete configuration".
Mass Configuration in ISX Central does not ... By design . ... x, mass configuration of APC devices ... ... is a mass configuration option for APC ... ... can pull the configuration from one device and push that configuration to one or more devices ... ... to edit the configuration after it is ... ... ) to mass configure the user name ... After ISX Central pushes the config , it will try to pull it from the device again to verify what it sent against what the device is providing in the configuration file. Since we can not pull this value to verify it, Central will show an "Incomplete Configuration " error message.