Consultar las preguntas frecuentes



Video: How to take the Galaxy 5000 UPS from total power off to normal operation.
Transitioning the Galaxy 5000 UPS from total power ... Galaxy 5000, Galaxy 5500 For various reasons, the Galaxy 5000 may be ... ... This is not for commissioning a new UPS . ... of a new UPS must be performed ... trained and qualified service representative. ... to restore the Galaxy 5000 UPS from total power ... ... This procedure is for a single UPS without an external ... Step 1 : Set the input Q 1 switch to On ... end of the UPS initialization with PFC start- up . ... “Start the UPS Step 5 : Turn the ... Step 8 : Set the ...
How to take the Single Galaxy 5000 UPS from normal operation to total power off using an external Maintenance Bypass Panel
... to take the Single Galaxy 5000 UPS from normal operation ... Galaxy 5000, Galaxy 5500 ... request come in for assistance with Powering Down the Galaxy 5000 UPS ... power down the UPS are available on ... ... This procedure is for a single UPS with an external ... Step 1 : Touch any ... to wake it up . ... “Stop the UPS Step 5 : Press the ... gray) button for 3 seconds to ... ... protected by the UPS . Step 8 : Unlock CB2 ... The UPS is now fully ... ... : Open the UPS door. ... Turn off Q 1 Switch
​Information for Noise level of UPS Galaxy 5000 NAM
UPS rating ( kVA ) 40 /50/60/80kva 100/130kva Noise level on a normal floor (dBA) with ...
Video: How to take the Galaxy 5000 UPS from normal operation to total power off?
... Down the MGE Galaxy 5000 UPS Galaxy 5000, Galaxy 5500 ... request come in for assistance with Powering Down the Galaxy 5000 UPS ... power down the UPS are available on ... ... This procedure is for a single UPS without an external ... Step 1 : Touch any ... to wake it up . ... “Stop the UPS Step 5 : Press the ... gray) button for 3 seconds to ... ... protected by the UPS . The UPS is now fully ... Step 5 : Set the ... ... Turn the Q 1 Switch to Off There is still stored energy in the capacitors, and batteries inside the UPS . Never remove any covers or panels.
MGE STS, Galaxy 3000, 4000, 5000 and Galaxy PW; Wiring information for egx100 to any 66061-supported products
Wiring information for egx100 to any ... ... – STS, Galaxy 3000, 4000, 5000 and Galaxy PW ... – STS, Galaxy 3000, 4000, 5000 and Galaxy PW Wiring information for egx100 to any ... ... card is configured for 9600, 8 , N and 1 . Slave address is 1 and wiring is ... ... This assumes only one 66061 card or UPS or STS is ... ... card is RS232 for configuration. One is down ( ... all others are up . ... required on the UPS /STS. The male DB9 connector is not supplied with the UPS but a black terminal block is supplied with the EGX.
Smart-UPS VT-Galaxy 3500; Bypass Not Available Input Freq/Volt Out Of Range, Output: Inverter sync. to bypass alarms
Smart- UPS VT- Galaxy 3500; Bypass ... Smart- UPS VT- Galaxy 3500-ais3000 ... of acceptable range for bypass operation. ... occurs when the UPS is online, ... , the UPS should not allow ... to command the UPS to bypass. If the UPS allows you to ... alarms are displayed for 20> seconds ... ... Input frequency range for the PFC is 40 Hz - 70hz ... ... window, the UPS should be in ... For 60 Hz systems ... ... - 0, 1 % For 50 Hz systems ... ... - 0, 1 % 40 Hz - 60 ...
Video: How do I upgrade the firmware on an APC Network Management Card (NMC) or NMC embedded device (Rack PDU, etc)?
or UPS Network Management Card v6. X . X Firmware for Smart- UPS & Galaxy 3500 with ap9630/31/35
Galaxy VX; How to set up, stop or change the “Automatic Battery Test” option of the UPS
How to set up , stop or change the “Automatic Battery Test” option of the UPS ... Galaxy VX - all ... How to set up , stop or adjust the Automatic battery test option ... Set your preferred settings for the automatic battery test: ... : Select your preferred interval for battery tests. ... Every 8 Weeks
Information for Noise level of UPS Galaxy PW
UPS rating in KVA 100 130 150 180 200 225 Noise level on normal floor (dBA) 62 63 64 65 67 68
Video: How to take Galaxy VM UPS out of Maintenance Bypass
... How to take Galaxy VM UPS out of Maintenance ... Galaxy VM ... equipment, the UPS must be transitioned ... maintenance bypass following service or other maintenance ... ... , takes about 1 -2 minutes to boot up screen. ... top of the UPS and turn the key so the UPS can now go ... This video provides a step by step instruction on how to operate the Galaxy VM UPS from Maintenance Bypass mode to on-line mode, to allow the end-user to transfer load back to the UPS from MBP without interruption: ... Also to transition UPS into Maintenance Bypass


Resultados 1 - 10 de 70

¿No encuentras lo que buscas?

Ponte en contacto con nuestro equipo de atención al cliente para obtener información sobre asistencia técnica, asistencia para quejas, etc.