Sfoglia le FAQ



How to take the Single Galaxy 5000 UPS from normal operation to total power off using an external Maintenance Bypass Panel
How to take the Single Galaxy 5000 UPS from normal operation to total power off ... Galaxy 5000, Galaxy 5500 Due to site maintenance, ... request come in for assistance with Powering Down the Galaxy 5000 UPS The instructions to power down the UPS are available on ... ... This procedure is for a single UPS with an external ... Step 1 : Touch any ... on the display to wake it up ... ... 3: Scroll to “Maintenance” ... “Stop the UPS Step 5 : Press the ... gray) button for 3 seconds to transfer the load to the Static Bypass ...
Video: How to take the Galaxy 5000 UPS from total power off to normal operation.
Transitioning the Galaxy 5000 UPS from total power off to normal on- ... Galaxy 5000, Galaxy 5500 For various reasons, the Galaxy 5000 may be ... ... guide illustrates how to restore it to normal operation. ... This is not for commissioning a new UPS . ... of a new UPS must be performed ... How to restore the Galaxy 5000 UPS from total power off to normal operation. ... This procedure is for a single UPS without an external ... Step 1 : Set the input Q 1 switch to On ... end of the UPS initialization with PFC ...
Smart-UPS VT-Galaxy 3500; Bypass Not Available Input Freq/Volt Out Of Range, Output: Inverter sync. to bypass alarms
Smart- UPS VT- Galaxy 3500; Bypass ... Smart- UPS VT- Galaxy 3500-ais3000 ... of acceptable range for bypass operation. ... occurs when the UPS is online, ... , the UPS should not allow you to command the UPS to bypass. If the UPS allows you to enter Static Bypass ... alarms are displayed for 20 > seconds) ... the input voltage to provide acceptable voltage ... ... Input frequency range for the PFC is ... ... window, the UPS should be in ... For 60 Hz systems ... ... - 0, 1 % For 50 Hz systems ...
MGE STS, Galaxy 3000, 4000, 5000 and Galaxy PW; Wiring information for egx100 to any 66061-supported products
Wiring information for egx100 to any 66061- ... ... – STS, Galaxy 3000, 4000, 5000 and Galaxy PW ... – STS, Galaxy 3000, 4000, 5000 and Galaxy PW Wiring information for egx100 to any 66061- ... ... card is configured for 9600, 8 , N and 1 . Slave address is 1 and wiring is ... ... This assumes only one 66061 card or UPS or STS is connected to the enclosure but ... ... card is RS232 for configuration. ... must be wired to . ... IP address needs to be configured at ... One is down ( ...
Video: How can the Galaxy VS reduce my energy bill?
Galaxy VS is a 20 to 100kva (400v ... 480v) or 10 to 50kva (208v ... 3-phase UPS for edge, small ...
Video: How to take the Galaxy 5000 UPS from normal operation to total power off?
... Down the MGE Galaxy 5000 UPS Galaxy 5000, Galaxy 5500 Due to site maintenance, ... request come in for assistance with Powering Down the Galaxy 5000 UPS The instructions to power down the UPS are available on ... ... This procedure is for a single UPS without an external ... Step 1 : Touch any ... on the display to wake it up ... ... 3: Scroll to “Maintenance” ... “Stop the UPS Step 5 : Press the ... gray) button for 3 seconds to transfer the load to the Static Bypass ... ... protected by the UPS .
Does the NTP need to be configured on the Galaxy VS internal NMC and the optional AP9644 NMC for all parallel or single Galaxy VS?
Resolution: Ensure that only one network management interface in the entire UPS system ( single or parallel) is set to synchronize time.
Does the NTP need to be configured on all NMCs for all parallel Galaxy VS?
Resolution: Ensure that only one network management interface in the entire UPS system ( single or parallel) is set to synchronize time.
Galaxy 3500, Smart-UPS VT and ais3000 Power Factor Information
Galaxy 3500, Smart- UPS VT and ais3000 Power Factor Information ... Galaxy 3500, Smart- UPS VT and ais3000 ... Galaxy 3500, Smart- UPS VT and ais3000 Power Factor Information ... The Input Power Factor is 1 . The Output Power Factor is 0.8 - what means that, for example, a 10kva unit can provide a maximum total load of 8KW. This means there is a difference of 20 % between real and apparent power. Refer to the following application note for a better understanding of power factor as related to APC products
Which SmartSlot accessories are supported by the Galaxy 3500 (g3500) UPS?
... supported by the Galaxy 3500 (g3500) UPS ? ... Facility 3 Phase UPS MGE Galaxy 3500 models ... supported by the Galaxy 3500 UPS (g3500) ... must be taken to utilize them. ... with the g3500 UPS . ... with the g3500 UPS . ... Management Card 2 to have dry contact ... inputs, ( 1 ) output per ... ... in the g3500 UPS . ... in the g3500 UPS . For ap9610 (or ... ... front panel/ UPS door will not ... In order to avoid this issue ... 1 .) Purchase ...


Risultati 1 - 10 di 67

Non trovi quello che cerchi?

Contatta l'assistenza clienti per ricevere informazioni, supporto tecnico, assistenza per i reclami e altro ancora.