Pesquisar Perguntas frequentes
Video: How to take the Galaxy 5000 UPS from total power off to normal operation.
Transitioning the Galaxy 5000 UPS from total power off to normal on- ... Galaxy 5000, Galaxy 5500 ... reasons, the Galaxy 5000 may be ... ... guide illustrates how to restore it to normal operation. ... commissioning a new UPS . ... of a new UPS must be performed ... trained and qualified service representative. How to restore the Galaxy 5000 UPS from total power off to normal operation. ... is for a single UPS without an external ... Step 1 : Set the input Q 1 switch to On ... end of the UPS initialization with PFC ...
How to take the Single Galaxy 5000 UPS from normal operation to total power off using an external Maintenance Bypass Panel
How to take the Single Galaxy 5000 UPS from normal operation to total power off ... Galaxy 5000, Galaxy 5500 Due to site maintenance, ... Powering Down the Galaxy 5000 UPS The instructions to power down the UPS are available on ... ... is for a single UPS with an external ... Step 1 : Touch any ... on the display to wake it up ... ... 3: Scroll to “Maintenance” ... “Stop the UPS ” Step 5 : Press the ... for 3 seconds to transfer the load to the Static Bypass ... ... protected by the UPS .
Smart-UPS VT-Galaxy 3500; Bypass Not Available Input Freq/Volt Out Of Range, Output: Inverter sync. to bypass alarms
Smart- UPS VT- Galaxy 3500; Bypass ... Smart- UPS VT- Galaxy 3500-ais3000 ... occurs when the UPS is online, ... , the UPS should not allow you to command the UPS to bypass. If the UPS allows you to enter Static Bypass ... the input voltage to provide acceptable voltage ... ... window, the UPS should be in ... ... - 0, 1 % 50 Hz - 70 ... For 50 Hz systems: 50 HZ +/- 0, 1 % ... = 228. 8 ... : Inverter sync to bypass error:
Does the NTP need to be configured on the Galaxy VS internal NMC and the optional AP9644 NMC for all parallel or single Galaxy VS?
Resolution: Ensure that only one network management interface in the entire UPS system ( single or parallel) is set to synchronize time.
Does the NTP need to be configured on all NMCs for all parallel Galaxy VS?
Resolution: Ensure that only one network management interface in the entire UPS system ( single or parallel) is set to synchronize time.
What type of battery could I use with the Galaxy VS UPS?
What kind of external batteries does the Galaxy VS 3-Phase UPS support? ... Galaxy VS ... Longer lifetime than classic battery solutions- matches service life of Galaxy VS UPS Higher predictability and manageability thanks to the built-in battery monitoring system
Which modular batteries can be used with the Galaxy VS All in One (AIO) model?
It is not possible to program different batteries into a UPS .
Galaxy VS; Why is FTP being logged in the event log but no external cause for logging FTP found?
Some UPS to NMC communications like Waveform generation are being logged by the NMC. FTP events should be communications between NMC and external applications ...
Video: How to take Galaxy VM UPS out of Maintenance Bypass
How to take Galaxy VM UPS out of Maintenance ... Galaxy VM To protect the attached equipment, the UPS must be transitioned ... maintenance bypass following service or other maintenance to the system. Power to the screen will ... , takes about 1 -2 minutes to boot up screen ... ... ) you need to turn the Kirk key next to the MBB and ... top of the UPS and turn the key so the UPS can now go ...
Video: How to take the Galaxy 5000 UPS from normal operation to total power off?
... Down the MGE Galaxy 5000 UPS Galaxy 5000, Galaxy 5500 Due to site maintenance, ... Powering Down the Galaxy 5000 UPS The instructions to power down the UPS are available on ... ... is for a single UPS without an external ... Step 1 : Touch any ... on the display to wake it up ... ... 3: Scroll to “Maintenance” ... “Stop the UPS ” Step 5 : Press the ... for 3 seconds to transfer the load to the Static Bypass ... ... protected by the UPS . ... bypass switch Q3BP to ON. ... output switch Q5N to OFF.