Browse FAQs



Why doesn't StruxureWare or ISX Manager's mass configuration feature update or show password credentials on APC Network Management Card devices?
Mass configurations of APC UPS ... devices done via ISX Manager or StruxureWare ... ... , ap9340, NetBotz 200) ... Network Management Card 2 (NMC2) ... ... Network Management Card 2 include (but ... to): 2 G Metered/ ... ... removed from the config .ini ... outside of the config .ini, This affects ISX Manager's ability to make mass configuration change of the ... . Because the ISX Manager takes one ... ... X, the config .ini ... blurb from a config .ini: The config .ini file could be manually configured outside of ISX Manager to include ...
Video: How do I configure APC Network Management Card network settings?
... , ap9340, NetBotz 200) ... Network Management Card 2 (NMC2) ... ... Network Management Card 2 include (but ... to): 2 G Metered/ ... ... TCP/IP settings prior to being ... ... available options to configure the Network Management ... with it's initial settings : the Wizard ... ... based devices are configured for a boot ... ... it is not configured on your DHCP ... ... methods below to configure /access the ... ... Network Management Card 2 /3 ... Network Management Card 2 and 3 based ... higher, are configured for DHCP Only ...
How can I mass configure a Network Management Card (NMC) or NMC embedded product?
How can I mass configure a Network Management Card (NMC) or NMC embedded product? ... can I mass configure or configure multiple Network Management ... ... , ap9340, NetBotz 200) ... Network Management Card 2 (NMC2) ... ... Network Management Card 2 include (but ... to): 2 G Metered/ ... ... MasterSwitch 1/ 2 ) do not ... ... Card, mass configuration of those devices ... ... configuration file ( config .ini) ... ... Network Management Card 2 firmware v6 ... ... modified through the config .ini ... , these four settings will be disregarded ... ... keyword will not configure Output Voltage, ... ... I obtain a config .ini ... to retrieve the config .ini
Data Center Expert | Surveillance frame rate when NetBotz communication is SSL
StruxureWare Data Center Expert surveillance slows when communicating to NetBotz appliance(s) using SSL. ... NetBotz (series 300 and higher) ... NetBotz (all versions) ... Regardless of the frame rate you have set within the Data Center Expert surveillance settings , the maximum frame rate Data Center Expert will receive from a NetBotz appliance is 5 frames per second. ... This is working as designed . Without the encryption and decryption in SSL, surveillance frame rates will remain as configured . This issue effects both version 2 and version 3 NetBotz appliances.
NetBotz | Scheduling Periodic Reports
NetBotz v3 Wall ... NetBotz v3 Rack ... NetBotz v 2 and v3 As designed , Periodic Sensor ... ... this limitation and configure your appliance to ... ... the Advanced Scheduling settings and return to ... ... your Periodic Report settings . When you specify an interval of 1,440 minutes (1 day) the report will run once every day, at the time you saved the configuration .
Netbotz | What type of information can I see in a NetBotz SNMP trap?
... found in a NetBotz SNMP trap NetBotz NetBotz SNMP trap ... traps from a NetBotz device are a ... ... the same when configuring traps for StruxureWare ... the alarm action configuration for a trap ... ... a similar trap configuration but it is ... rather than the NetBotz OIDs. ... This article is designed to provide some ... VarBinding 2 : 1. ... ... .13 = 2 ... look at the NetBotz MIB, you ... that the trap parameters are listed under ... ... .netBotzAPC. NetBotz .netBotzTrapParms ... .11. 2 Please note that you NMS or trap receiver must support this type of nested trap in order to get this information from the NetBotz appliance.
Why can't I connect to my APC Network Management Card or embedded Network Management Card using a serial connection?
... , ap9340, Netbotz 200) ... Network Management Card 2 (NMC2) ... ... Network Management Card 2 include (but ... to): 2 G Metered/ ... Ensure you are connecting at the correct settings ... Please reference the product’s user manual for the default settings . ... by the user, a change to the configuration file, or a managing device like ISX Manager or StruxureWare Central. ... If you are having an issue connecting, try setting the baud rate to a different value:
Why is HP Systems Insight Manager not receiving SNMP traps?
... , ap9340, Netbotz 200) ... Network Management Card 2 - ap9630/ ... ... Network Management Card 2 include (but ... to): 2 G Metered/ ... ... infrastructure management platform designed for monitoring hardware ... ... proper Event Handling configuration and Management Information ... ... ” folder and configured using mcompile ( ... ... > SNMP Trap Settings ). ... needs to be configured to detect the ... Under “ Configure /Repair” all SNMP configurations must be enabled ... ... SIM must be configured to accept SNMP ... Under “Event Filter Settings ,” make sure all IP ranges desired are being accepted ( * indicates acceptance from any IP).
IPMI Overview
Netbotz NetBotz Version 2 and 3 appliances ... protocol supported by NetBotz appliance for monitoring ... ... relatively new technology designed to extend customers ... ... software applications ( NetBotz ). NetBotz Support of IPMI IPMI allows NetBotz to monitor physical ... NetBotz appliances polls the ... similar to how NetBotz polls SNMP devices ... NetBotz BotzWare 2. ... ... provide recommended threshold settings . ... created on the NetBotz appliance. ... supported on the NetBotz 500, 420 ... IPMI is supported on the NetBotz 450, 455, 550, and 570 units with a 5 node monitoring pack (nbwn0006) installed. ... IPMI must be supported and configured on the target device.


Results 1 - 10 of 50

Can't find what you are looking for?

Reach out to our customer care team to receive information on technical support, assistance for complaints and more.