Consultar las preguntas frecuentes
Why is my equipment dropped or rebooted while connected to my Smart-UPS?
1 ) ... be able to support the load attached ... ... once every 6 months while in storage ... ... be plugged into it . ... is capable of supporting a load of ... ... you're trying to support , please use ... ... printer connected to it . The computer ... A single piece of equipment ... If one input cord is ... ... a UPS on one input and Utility ... It will begin with ... ... UPS thus causing it to shutdown and ... ... to battery, it may have an ... ... very uncommon with IT equipment. A change of state causes ... ... type of connection it is important to ... Each UPS must have its ' own pair of wires running back to the EPO switch.
MGE STS, Galaxy 3000, 4000, 5000 and Galaxy PW; Wiring information for egx100 to any 66061-supported products
This assumes only one 66061 card or UPS or STS is connected to the enclosure but if more than one change as required.
SMTP Port option in PowerChute Business Edition version 9.2, 9.5, 10.x
How to change SMTP port options in PowerChute Business Edition ... All supported OS ... Need to changed SMTP port settings ... identifies the SMTP server by one of the three methods mentioned: its name, its ipv4 address, or its ipv6 address. ... It is the e-mail account to be used to send notifications. ... Port numbers can have a maximum of five digits and can be set to 25, 465, 587, or any number ranging from 5000 to 32768. ... You can enable it by selecting the Basic E-Mail for Authentication
Why Node-red embedded with Ecostruxure Augmented Operator Advisor stop few second after starting?
When you start AOA, there is one MS-dos windows with a lot of information ... Go to …Schneider-electric \ Ecostruxure Augmented Operator Advisor \ Node-red \ node-red home ... Change the name or remove the flow named flow_w7frn05933l.json ... Change the name of the backup .flow_w7frn05933l.json.backup
Is it possible to convert a NetShelter SX Networking cabinet into a standard NetShelter SX cabinet?
... cabinet will not change so it could be confusing on future tech support calls. It's not possible to modify a NetShelter SX cabinet into a NetShelter Networking cabinet beacuse the parts are not available as spares. ... 1 ) The ar758x-series can be mounted onto the replacement rails. ... After conversion the cabinet has a serial number and sku label show that it's a Networking cabinet, but it's not. Any calls for Tech Support for this cabinet will need to explain that the cabinet was modified, and how.
SmartConnect Portal indicates that the firmware is out of date on my SmartConnect enabled UPS. How do I update it?
... SmartConnect enabled ( EcoStruxure ™ Ready) ... EcoStruxure ™ Ready Smart ... EcoStruxure ™ Ready Smart-UPS products are able to download the latest UPS Firmware from the Cloud. ... https://www.smartconnect- support .apc.com/help/EN/index.html#page/ EcoStruxure %2520ready%2520smart-UPS%2520help%2520center%2fmn04.6.2.html%23 ... 1 - To upgrade the firmware you can do so via the cloud portal.
Video: Data Center Expert | Monitoring an APC device with snmpv3 after it was discovered using snmpv1.
... using snmpv3 after it was discovered using ... Changing monitoring protocol from SNMP version 1 to SNMP version ... You can change the protocol the ... You can change the protocol only ... snmpv1 devices that support snmpv3. ... APC SNMP device supports snmpv3, consult ... ... you begin, it is recommended to ... 1 ) Open the ... ... Expand Authentication options 1 -4, ... box for the one you would like ... ... of the configuration change . ... to verify the changes due to security ... ... of "Not Supported " means that ... to verify the changes were successful due ... It has been seen ...
Data Center Expert | What virtualization environments are supported?
... virtualization environments are supported for the Data ... ... recent information on supported virtualization platforms can ... found within the EcoStruxure IT Help Center at ... ... virtual appliance, supported on VMware ESXi ... ... device nodes and one surveillance node. ... nodes and activate supported applications, or ... ... is the first supported virtualization platform. The Data Center Expert virtual appliance is delivered as an OVA (Open Virtualization Archive), expected to function properly on any virtualization platform that supports this format, or has an appropriate converter utility. ... There is currently no planned support for any other virtualization platforms, including Microsoft Hyper-V.
Network Attached Storage Support for NetBotz Version 2 Monitoring Appliances
... Network Attached Storage Support for NetBotz Version ... ... there is no support for SMB2) ... NAS Support Specifications: Supported on NetBotz 500 prior to Botzware version 2.6 and on the NetBotz 420 starting at Botzware 2.6 ... Maximum of 5000 objects can be stored ... It was changed on version 2.5 and is now only limited by disk space
Why isn't the time changing on my Network Management Card (NMC) when I change Daylight Saving Time (DST) settings?
... Network Management Card 1 (NMC1) ... ... Network Management Card 1 include (but ... After changing daylight savings time settings, the card takes roughly 60 to 90 seconds to jump the system forward or backward 1 hour. ... It is also recommended to update the network enabled device to the latest firmware found on the Software & Firmware section of the APC website. If the problem persists, please contact APC Technical Support .